I have managed to get an old OnePlus5T phone up and running with PostmarketOS and have hosted a couple of services there.

If it possible to charge and give Ethernet connection using those multi port extensions on a phone?

Thought I’d ask before investing in one as I am on a super tight budget.

  • CallMeAl (like Alan)@piefed.zip
    link
    fedilink
    English
    arrow-up
    22
    ·
    4 hours ago

    hgkPqNfhAQFJyqm.jpg

    I’ve had good luck with these inexpensive hubs which include ethernet for about 12 euro. However it does not work will all phones so you must test.

  • frongt@lemmy.zip
    link
    fedilink
    English
    arrow-up
    16
    ·
    4 hours ago

    Yes, but impossible to say if it’ll work for sure without testing. It depends on the phone, os, and driver for the chip in the dongle.

    But I can personally say that I’ve been able to use them with my Pixel running GrapheneOS. I’ve even successfully used a usb-c Ethernet adapter with an iPhone.

    • jol@discuss.tchncs.de
      link
      fedilink
      English
      arrow-up
      2
      ·
      4 hours ago

      This is also true for laptops BTW. I remember older Dell XPS laptops used to be super picky about USB-C dongles with

      • ferret@sh.itjust.works
        link
        fedilink
        English
        arrow-up
        1
        ·
        39 minutes ago

        Not really, drivers for ethernet chipsets are OS-dependent. Any x86 laptop is going to implement USB correctly because the controllers are built into the CPU

  • LumpyPancakes@piefed.social
    link
    fedilink
    English
    arrow-up
    6
    ·
    edit-2
    4 hours ago

    Works fine on my Motorola g50 using a Belkin usbc Ethernet adapter with charging passthrough.

    After a few days a message pops up that it will reduce battery to 80 percent to preserve it.

    Used as a 5g router.

  • Shimitar@downonthestreet.eu
    link
    fedilink
    English
    arrow-up
    5
    ·
    4 hours ago

    If you get the USB working, beware of bulging battery: its not a IF but a WHEN if you keep it plugged 24/7.

    Also,mostly depend on postmarket is kernel drivers what will actually work over USB.

    • tomandjerryco@mander.xyzOP
      link
      fedilink
      English
      arrow-up
      3
      ·
      3 hours ago

      The battery of OP5T can’t be removed. May need to either replace it with a “dead” battery or muck about with the software to make to never charge over 80%.

      Thanks for this suggestion.

      • CmdrShepard49@sh.itjust.works
        link
        fedilink
        English
        arrow-up
        5
        ·
        3 hours ago

        Probably much more involved with the OP5T, but when I looked into running my Note 4 as a display without a battery, I discovered that you just needed to show a couple pins a 3.7V signal and it’d think there was a battery installed. This can be accomplished with a dime-sized voltage converter connected to the input power.

      • Shimitar@downonthestreet.eu
        link
        fedilink
        English
        arrow-up
        2
        arrow-down
        3
        ·
        3 hours ago

        The 80% is useless, batteries are not built to be charged continuously. I suggest you use a smart plug that you turn on and off periodically

  • Mordikan@kbin.earth
    link
    fedilink
    arrow-up
    1
    ·
    3 hours ago

    You can but its dependent on the phone and USB-C adapter being used. Originally I was attempting to use 5G cellular as backup internet via a refurbished Samsung A54 5G. I was able to build the GRE tunnel between the phone and router, but the phone would either charge or provide ethernet, not both.