We all know WD-40 works for making things move when they’re seized, but it also works better than anything for getting rid of all traces of adhesive left behind after peeling off stubborn stickers from things you buy.
It works on nearly all surfaces* – even coated paper! (just be sure not to leave it to soak into the paper.)
Instead of peeling slowly for ages with your fingernail or doing that peel-stick-peel-stick thing for half an hour, soak a paper towel in WD-40 and dab it on the offending sticker remains, wait a few minutes, then wipe off. (*if on coated paper, don’t let it soak, just gently rub it.) Clean the item afterwards to remove the oil left behind.
*it’s best to test a small area first if the object is painted or porous, and be careful with items meant to be food safe, because WD-40 is obviously not food safe.
This is something I wish more people knew, because soooo many manufacturers and retailers put stickers in the worst places and with near-permanent adhesive. I hope this helps you!
You should know that wd is for water displacement. If you are trying to do anything else there is a better chemical you should use instead.
Thank you! I actually needed this for some things at work. Godspeed, kind internet stranger.
I found out bike chain oil works wonders for this as well. I also found out that bike chain oil will make you mildly high at the same time.
That’s not really a bonus. WD-40 will likely also get you high in close quarters – it’s probably more expensive than weed, though, and likely kills more of your brain than is worth it.
I recommend a high THC, mushrooms, or LSD instead. Combustible inhalants are a worse high that will probably give you a headache and then cancer. No bueno.
Oh it wasnt on purpose. Im not advocating it.
If you don’t have any, or want a food safe alternative, soak the remaining sticker in cooking oil.
Isopropyl alcohol also works.
Oh, I didn’t know about cooking oil, that’s awesome.
Alcohol works, but it will destroy many finishes (painted or stained furniture, coated paper, some coated metals, some plastics and rubbers, etc), whereas WD-40 is safe for most finishes.
Sounds like cooking oil may be as well – gonna have to try that, thanks!
Cooking oil helps with scrubbing it off so that it doesn’t continue to stick. Good for scraping off the residue.
Let is know once you test it, thanks
I’ve tested it on nearly everything over the years. It works on everything so far. I didn’t have any a bit ago and used alcohol instead, and it ruined the rubber surface. That’s why I posted this. I should have been less impatient and waited till I had some. Posted so others can learn before they ruin something like I just did.
The cooking oil?
I’m sorry, I answered your question from my inbox instead of in context in this thread, so I lost context.
I haven’t tried cooking oil, just WD-40. I’ll try cooking oil as you suggested.
I have some vegetable oil I fried chicken in to make chicken parmesan and since I was lazy the marinara came in a glass bottle that I peeled the label off to keep/reuse. The glue survived the dishwasher yesterday, so I’ll go lay that side in the used vegetable oil and report back in a few hours when I try to get it off.
#excitingfridaynights
Edit update: said glue/jar/oil
Will remote back in a bit
deleted by creator
Hand sanitizer frequently works too.
Too much water. Not good with paper labels.
That’s got 70% isopropyl in it. Sometimes perfumes too.
It’s also great for shitty faded plastic headlights. It’s not a long term fix but it’s an immediate fix when applied. I redo every few months.
I’ve had good luck with Goo Gone.
It has an extremely strong citrus smell (which I don’t think is an additive for smell, as it’s overpowering).
kagis
No, according to them, orange extract is one of the solvents.
https://googone.com/media/ingredient/goo-gone-goo-and-adhesive-remover-spray-gel-ingredients.pdf
Goo Gone is what I’ve used for years. It’s quite effective at the getting rid of the super stubborn ones.
I came here to mention Goo Gone. Used it a lot.
My go to for cleaning sticker residue off glass is wd-40 and a fresh razor blade. Works like a charm and is scratch free.
Mine is either Isopropanol alcohol and/or hot water (only with glass) + a lint free rag
The hot water get’s inside the container to heat up the glue.
The isopropanol is to get rid of the glue.
Isopropyl alcohol is all you need, and is less aggressive than WD-40.
Alcohol is far more aggressive and will ruin many plastics, rubber, painted surfaces, finished wood, and coated paper.
Be really, really careful using alcohol on anything other than bare metal and some plastics. Many plastics and rubber will be made eternally sticky with alcohol (I made this mistake earlier today, which was why I posted this).
It is not a matter of more or less aggressive, some materials dissolve more easily in one type of solvent than in others. You can try, dissolving a teaspoon of salt in water is much easier than in oil. Have you ever eaten chocolate or drunk water while chewing bubblegum? Here the opposite happens, the fats in the chocolate dissolve the bubblegum rubber and make it softer while water doesn’t, it just chills it which makes it firmer.
Now plastic, rubber, or paints, finishings… can be many different things. IPA is safe to use on natural rubber while oils will make it swell and degrade, or even melt it. But most rubbers are synthetic, basically rubbery plastic. These plastics and other engineered materials can have all kind of different properties, while looking exactly the same. So the only thing you can do, other than research on that particular material and solvent, is trying it on a safer or hidden part of the thing.
In my experience: oil isn’t good on most rubbers, IPA is ok. For metals (iron, steel, mechanical parts…), contrary to you I usually advise to clean them with oil/grease, alcohol is appropriate if you don’t want it to be oily, only in rust resistant metals. Consumer/industrial products paints and finishings are usually fine with both ipa and oil if applied swiftly and dried quickly– acetone, kerosene, toluene… will strip them away probably. For wood, almost everything will fuck it up.
xylene or toluene or denatured spirits or acetone or basically any solvent you can buy at hardware store works for this really
check to make sure they don’t fuck up plastic though
They often fuck up plastic, rubber, fake leather, definitely paper, and painted or finished surfaces. WD-40 is usually safe on those surfaces (or as others have said, Zippo lighter fluid and possibly cooking oil).
Alcohol removes adhesive, but is likely to ruin the surface too.
Lighter fluid works great as well
True, but lighter fluid can ruin many surfaces. WD-40 is weirdly gentle on most surfaces (though it doesn’t seem like it would be).
I’ve never seen naptha (i.e. Zippo lighter fluid) do anything to any painted or finished surface, nor any of the plastics I’ve ever tired it on. I’ve been using the stuff in that context for decades, to the extent that I literally purchase it by the gallon. (I also use it in my lighters, because painter’s naptha is like 2% of the cost per volume of brand name Zippo fluid despite being the same stuff.)
WD-40 contains nonvolatile oils that will leave a difficult to clean off residue behind and if you use it on anything porous it will soak in and possibly stain the surface while being functionally impossible to remove without using yet more solvents. For that reason it’s not really a great way to get stickers off of things, especially things that you’d like to remain non-greasy or may need to stick something to again at some point in the future (paint, tape, etc.).
Naptha will evaporate entirely on its own given enough time, and you can even use it on paper and printed surfaces (excluding inkjet printed things, in my experience, which it will smear) with no harm done after it fully dries.
If you took the sticker off but the adhesive is left over just keep resticking and peeling it off. Do it quickly just push down and off.
That doesn’t always work. Some of these adhesives are stupidly sticky, and some leave all of their paper rather than giving up.
If it’s a weak adhesive, that method is fine. This tip is for strong or obnoxiously sticky adhesives, and especially on surfaces that don’t want to give up or that could be damaged easily.
It’s also great for taking crayon drawings off walls.
Have children to learn hacks ;)
More sticky children hacks, please. :)
If your car ever gets spray painted, WD-40 is also very good at removing that. Just spray it on a lint-free rag and gently wipe the spray paint and the WD-40 will dissolve the spray paint and whisk it away with a minimum amount of effort.
